How do you actually feel on the subject of How to Install a Bathtub Yourself?
Installing a bath tub isn't specifically rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bath tub with a new one is also a reasonably tough job. If the old bathtub is conveniently obtainable, the job can relocate immediately; if you need to open a wall surface to get rid of the old tub and position the new bath tub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old tub as well as set in the brand-new one. Make certain you have qualified yourself for the job and also are comfortable trying it. As opposed to hiring a service provider to take control of a halfway-completed job, it is much better to think about utilizing one before you start. Possibilities are you may need a professional plumber to make tube links.
This short article will assist you set up a brand-new bathtub in your shower room if you have currently gotten a brand-new tub and also do not require to alter the arrangement of your previous water supply pipes.
Your devices and material checklist must consist of the following:
Planning for the Installment
First of all, the supporting framework provided with the bathroom should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to prevent strain on the tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its final placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you ought to do is detach the water supply. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be quite troublesome because of the restricted access that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel ready for the remaining water that will come from the pipes. As soon as the supply pipes have actually been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of the two wood boards under its feet, position the tub in the needed position. The wooden boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bathtub till the spirit level reviews level.
To set up faucets, fit the bottom of the furthest versatile faucet port to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and examine all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and likewise examine the overflow outlet and the regular outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub needs to wait until the tub has been utilized at the very least when as this will resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap as well as the sink. Secure the faucet in place with the manufacturer supplied backnut. As soon as the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet adapters. The former kind ought to be linked to the faucet ends first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break a rigid seal, creating the water to penetrate the wall surface in between the bathroom as well as the tiling, causing issues with dampness and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and also cartridges, and can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the bath tub with water prior to sealing, to permit the activity experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that review about How to Install a Bathtub while exploring the internet. Sharing is good. You won't know, you will be doing someone a favor. Thanks so much for taking the time to read it.
Ready when you are!